Complete Design for Woven Fabrics

Posted on

Design is prepared for producing woven fabrics. Design is done on paper. A complete for woven fabrics should consist of weave plan, drafting plan and lifting plan

1.Weave plan: Weave plan takes the interlacing of the ends and picks into consideration. It contains ups and downs of each yarn in fabric and the number of ends and picks of a design utilized. It is repeated for the complete design.
2.Drafting plan: Drafting plan shows the number of healded shafts which are used and the order in which the warp ends are threaded through heald eye of the heald shafts.
3.Lifting plan: Lifting plan also known as Peg Plan defines the selections of heald shafts to be raised or lowered on each successive insertion of pick.

Some factors should be taken into consideration during designing.
1.Denting plan: The process inserting warp yarn though reed is called as denting. Denting plan must meet the requirements on orders.
2.Structure: In the manufacture of fabric by weaving on a loom, the techniques interlacing two series of threads at the right angles to each other are called as structure.
3.Texture: The tern texture signifies the general quality of a fabric, developed by the interplacement of yarn used. Weight, bulk and hand feeling are also expressed by the term of texture. Materials, count of yarn and relative density of threads are its main factors.

So only following the design plan of the fabric can know about the woven fabric. In the modern times, various types of complex design are produced. Different kind of woven machines can be used for design, including jacquard loom, dobby loom, water jet loom or air jet loom.

Wrong selection loon will damage to the woven fabric.

Properties and Ornamentation Techniques of Plain Weave

Posted on

Compared with other types of woven fabrics, the structure of plain weave is the simplest. Most of the woven fabrics are made of plain weave and very tight fabric is also formed by plain weave. In plain weave, weft yarn passes through the warp alternatively.

Types of plain cloth:
Plain cloth made of plain weave is commonly seen in the market. Plain cloth is classified into:
1.Muslin
2.Linen
3.Alpaca
4.Taffeta
5.Calico
6.Long cloth

Properties of plain weave:
1.Both side of the weave are identical.
2.It improves the total output of woven fabric.
3.Plain weave is used as different kinds of textile raw materials and yarns, cotton, linen, jute, synthetic fibers, spun and continuous filament yarn, etc.
4.Thread interlacement is in alternative order.
5.The adjacent threads receive the maximum amount of support from each thread.
6.Structure of plain weave is stronger and better than any other structure.
7.Friction as well as stress on warp yarn is reduced by skip draft.

Ornamentation techniques of plain weave:
Various types of plain weave are commonly seen is the market. They have different outlook though they are made by the same design. The outlook of the plain fabric is changed by using ornamentation techniques.
1.Using extremely fine yarn, i.e. Muslim cloth.
2.Using coarse yarn, i.e. Jute Hessian.
3.Using threads of different colors which are combined in check form.
4.Using the threads on both warp and weft that may be varied in color and count.
5.Using Fancy Slub yarn.
6.Using two warp beam in different tension.
7.Using different twisted yarn.
8.Using special shaped reed.
9.Using different textile materials.

Preferential Policies Decrease Xinjiang Textile Cost

Posted on

On 14th August, Liang Yong, the deputy director of the Commission of Economy and Information Technology stated that, the industrial preferential policies on Xinjiang textile and clothing will decrease the cost of textile products by about 10%.
20140815164639

In A share market, there has been four listed companies of textile industry disclosing their interim results and nine companies published earnings pre-annunciation reports. As a whole, enterprises of textile fabrics still stay at the slack season. Raw materials and cost of labor remain to be two big problems in textile industry.

Known from Xinjiang Textile Industry Management Office, cotton price was declining all the time in the first half of 2014 due to insufficient market demands and price difference at home and abroad. In this case, Xinjiang textile and clothing industry went on a low status in which enterprises lacked of growth power and circulating capital. The whole field were faced with loss.

Insiders analyzed that the preferential policies on Xinjiang textile and clothing industry have greatly inspired market confidence. Textile enterprises have grasped this information and made efforts on improving complete textile and clothing industrial chain.

On 6th August, the first clothing production line of Aksu was put into operation. This line is located in Aksu industrial zone. What’s more, Aksu industrial zone is striving to attract investments on weaving, printing and dyeing, clothing manufacture, textile facilities, digital printing, carpet, etc. In order to guarantee sufficient raw materials supply, the zone also promotes the production of chemical fibers such as polyester, spandex, nylon and so on.

Derivatives of Plain Weave

Posted on

The structure of plain fabric is quit simple. Various types of derivatives of plain fabrics are produced to meet the different requirements of customers. Modified plain fabric has a great demand in the market. Based on different design, the derivatives are classified.

Derivatives of plain fabrics: Derivatives of plain fabrics are classified into rib weave and matt rib

Rib weave: Rib weave consists of ribs or cord in the warp or weft direction. Rib weave is classified into warp rib and weft rib.
Warp Rib
1.Regular Warp Rib
2.Irregular Warp Rib

Weft Rib
1.Regular Weft Rib
2.Irregular Weft Rib

Matt Rib: Matt rib has a smooth surface and it is more flexible than plain weave. Matt rib is classified into regular matt, irregular matt, stitched matt and fancy matt further.

Features of Divided Draft and Combined Draft

Posted on

Drafting system consists of divided draft and combined draft. Neither divided draft and combined draft is sued as straight, skip, point, broken, grouped and curved draft.

Feature of divided draft:
1.Divided shaft is divided into two or more groups.
2.Each group needs a suitable type of draft.
3.Divided shafts is mainly used for divided weaves, double warp weaves, and two ply weavs, pile weaves and some others.

Features of combined draft:
1.The draft which combines two or more drafts for producing a certain type of fabric is known as combined draft.
2.Combined draft is a type of complicated drafts.
3.The draft is chosen for technological or economical reasons.
4.Designer should have great knowledge about the drafting plan.

Posted in:

Routine Maintenance of Circular Knitting Machine

Posted on

Maintenance of Circular Knitting Machine Parts

a. change down the syringe, the needle plate to clean, coated with oil, oil cloth, placed in a wooden box, to avoid being bruised, deformed. When used, the first with compressed air to the oil syringes, needles within the disk is removed after the installation, adding knitting oil re-use.
b. change color varieties, the need to change down triangle classified storage (knit, tuck, float), and joined knitting oil to prevent rust.
c. does not run out of new needles, sinkers, you need to replace the original packaging bag (box) inside; change down when changing varieties knitting needles, sinkers, oil must be cleaned, checked and damaged after the pick, classification into the box, plus knitting oil rust.

circular knitting machine maintenance of electrical systems

Electrical system is the power source of circular knitting machine must be strictly regular maintenance, in order to avoid failure.

a. out regular checks on whether the equipment leakage phenomenon, if found, must immediately repair.
b. Always check around the detector is safe and effective.
c. Check whether the failure phenomenon switch button.
d. Check and clean the internal parts of the motor and the bearing refueling.
e. There is no wear and check the line disconnection.

Maintenance six other parts of circular knitting machine

1 Rack
a. market mirror oil oil oil standard position to reach the required standard to check the oil every day, to keep the oil level between the highest and lowest oil level when refueling, unscrew the screw hole filling, while rotating machinery, while fuel is added to the provisions of location.
b. the transmission gear (oil stains style) needs a month plus a lubricant.
c. lens cloth tank of fuel oil in the oil to reach the target position, you need a month plus a lubricant.

2 rolling machine
Check weekly oil cloth face once, depending on the oil situation refueling. In addition, under the circumstances to the chain, sprocket grease.

Posted in:

What Are the Characteristics of Warp Rib?

Posted on

The derivatives of plain weave are classified into warp rib and weft rib. Warp rib and weft rib can be classified into regular rib and irregular rib further. The structure of regular rib differs from the structure of irregular rib.

Characteristics of warp rib:
1.Warp rib can produce ribs or cords in the weft direction.
2.The quality of warp yarn is higher than weft yarn.
3.The number of ends is higher than picks in a unit space. Then, yarn having same count may be used.
4.Two or more weft yarns pass over or under a warp.
5.Weft yarns are low twisted yarn.
6.The design uses two heald shafts.
7.Mercerized yarns are used.
8.Warp rib is mainly used in warp faced construction, such as Poplin fabric.

In the regular warp rib, the number of warp yarn is the same in each line while the number of warp yarn is not the same in the irregular warp rib. For that, the structure creates the floating characteristics on the fabric so that fabrics are more comfortable than the basic plain weave cloth.

Factors Affects the Prominence of Twill Weave

Posted on

Diagonal lines on the face and back of the fabric are produced by twill weave. For that, the structure of twill weave has less comfort than plain weave. The prominence of the twill fabric is one of the important factors.

Characteristics of weave: Characteristics of weave have great influence on the prominence of the twill fabric. Twill lines having short float cause less prominence of twill line while having long float creates more prominence of twill line, weaker fabric, create looseness.

Characteristics of yarn: Prominence of twill weave has close relationship with type of yarns. Twill line having single yarn causes less prominence and having folded or ply yarn causes more prominence. Both same direction of twist and twill line and the finer and hard twisted yarn result to less prominence of twill weave. But opposite direction of twist and twill line and coarser and soft twisted yarn increase the prominence of twill weave.

Number of ends and picks per inch: Bothe EPI and PPI have great influence on the prominence of twill weave. The more EPI and PPI are the more prominence of twill weave is. Less EPI and PPI causes less prominence of woven structure.

Posted in:

The Methods Used for Indicating Drafting Plan

Posted on

Drafting plan is a major part of a completer design for a woven fabric. Drafting plan indicates the number of healds shafts which are used to produce design.

Methods of indicating drafting plan: Ruling line, design paper and numbering are used to indicated drafting plan.

Ruling Line Method: Ruling line is method of indicating draft, in which the horizontal lines and vertical lines represent the healds and the warp threads respectively. The marks on the line indicate the healds upon which the respective threads are drawn. It is less used for indicating drafting plan.

Design paper: Design paper in one of the most suitable ways to express drafting plan for a woven fabric. The horizontal spaces represent the healds while the vertical spaces represent warp threads. Marks can also be inserted upon the small squires.

Numbering: Numbering refers to the quantity of threads. The threads are successively drawn on the held to indicate number.

Systems of Drafting:
1.Straight Draft
2.Point Draft
3.Skip Draft
4.Broken Draft
5.Grouped Draft
6.Curved Draft
7.Divided Draft
8.Combined Draft

Features of Mock Leno Weave and Huckaback Weave

Posted on

Mock leno weave and huckaback weave are two important types of fancy weave which are used as raw materials for towel. Both two weaves have rough structure.

Feature of Mock leno weave:
1.The fabric has rough surface because it is like net or perforated.
2.Normally repeat size even number. The smallest repeat size is 6×6.
3.The weave can be used as towel for its excellent hydroscopicity.

Features of huckaback weave:
1. The fabric has rough surface.
2. Normally repeat size odd number, then better structure formed.
3. It can be used as towel for its excellent hydroscopicity.

The fancy design is different from the basic weave and this type of weave is performed for special purpose.