Vrae

If you do not consider the special circumstances of particular organizations brought only consider the needle incorrect due to wrong flowers and squandering the case, there are the following possibilities:

'n. poor knitting machine needle selection with the degree of synchronization itself, will lead to irregular squandering the entire disk, then re-adjust the parameters to the machine.

b. jacquard depth selector plate is not pressed, it will result in a lateral squandering. Jacquard middle pin is pressed into tablets linked, if the middle pin is depressed is not enough, the final intermediate needle still be quite straighten triangle knitting needle, appears certain large ones flowers confusion, squandering transversely.

c. Jacquard abnormal wear piece (jack or pins are similar phenomenon), will cause vertical squandering.

d. loom assembly design problems, resulting in an overall pattern confusion, this problem is relatively rare.

en. reset triangle or jack three track design or processing problems, resulting in particular large ones squandering. Problems in the case of being worn or fitted rear triangle design appears.

f. (position selector will jacquard sheet when pressed into the deepest barrel) relative to the needle selection jack triangle, the two are too close, leading to squandering. Middle pin needle selection is not completed action (being pushed jacquard pieces linked) has entered jack triangle track, leading to squandering, usually lateral squandering the entire disk.

g. selector and jacquard pieces assembled position with the heel of the poor, leading to squandering. For example selector at the head of this should not be pressed to lift jacquard piece, but because the low mounting position selector leads down to the jacquard piece, which appeared certain large ones squandering.

Compared with natural fabric, the process of printing synthetic fabric is easier. It is know that printing process depends on the characteristics of fiber. In cotton printing, the fabric needs to be pre-treated before printing while the pre-treatment of the fabric is not essential for synthetic fabric, because synthetic fabric does not contain impurities like natural fiber.

Process of printing synthetic fiber: Synthetic fiber has various types, and the printing process for synthetic fiber is not the same. The process of printing nylon varies from the process of printing polyester. And it also depends on the dyes and pigments.

The followings are the common process for printing synthetic fabric.

Fabric from weaving section
↓
Stitching
↓
Washing
↓
Jet Dyeing
↓
Stentering
↓
Druk
↓
Polymerizing
↓
Washing
↓
Stentering
↓
Agenda
↓
Folding or Rolling
↓
Packing

Polymerizing different monomer can produce synthetic fibers. After printing, finishing is done for adding some properties. So the printing sequence should be aware of.

Printing is a part of wet processing technology which is carried out after pre-treatment of fabric or after dyeing of fabric for producing attractive designs on fabric or other materials. Printing is described as localizing dyes or pigments which are applied locally or discontinuously to produce various attractive designs on fabric. Main objectives of printing are producing attractive designs with well defined boundaries made by the artistic arrangement of a motif or motifs in one or more colors. If dyes and pigments are applied properly on fiber, printed fabrics are protected from friction and washing. A strong bonding is formed between dyes and fiber.

Steps of textile printing:
Eerstens, pre-treat fabrics before printing.
Use printing ingredient to prepare printing pasts. Printing performance depends on a well printing paste.
Use any printing methods to make an impression of the print pasts on the fabric, which is required.
Carry out steaming on printed fabric to fix the printing paste on the fabric.
After-treatment process neutralizes printed fabric.

Styles of printing: There are three different styles of printing: direct style of printing, discharge style of printing (including white discharge and color discharge) and resist style of printing (white resist and color resist)

Methods of printing: Using different instrument carry out printing. Use different method to produce impression on fabric. Demands of users vary methods which rely on the type of materials and the purpose of end product usage.

The followings are the methods applied for textile printing operation.
Block Printing
Burn-out Printing
Blotch Printing
Digitale druk
Duplex Printing
Engraved Roller Printing
Electrostatic Printing
Flock Printing
Ink-jet Printing
Jet Spray Printing
Photo Printing
Rotary Screen Printing
Screen Printing (Flat Screen)
Stencil Printing
Spray Printing
Transfer Printing
Warp Printing
Special Methods (Tie dyeing and Batik Printing)

In the early of history, printing was carried out by hand. Deesdae, different modern techniques are widely used for printing, which are controlled by computer. Graphics design is also widely used. Textile machines improve printing methods a lot.

Pigmente is hoofsaaklik organiese materiaal wat sintetiese geen affiniteit het op die katoen. For this, binder word gebruik vir die maak van die film op die oppervlak van pigment sodat produseer 'n 3-dimensionele kruis skakeling tussen vesels en pigmente. Na droging, genesing is onder gedra 150-180℃ vir die vasstelling van die pigmente op die oppervlak van katoen. Prys van pigment drukwerk is laer as dié van ander drukproses.

Die volgende is die proses van die pigment druk op katoen:

Resep: Resep kan gevolg van die diepte van kleur verander
Verdikking: 2%
Binder: 8%
Vaste: -2%
Water: 90%

Stof Pre-behandeling
↓
Table voorbereiding
↓
Stof gevleg op die tafel
↓
Pigment druk smeer met die hulp van die skerm
↓
Genesing by 160 ℃ (bandspoed 6.50 m / min)
↓
Lewering

Printing is a method of wet processing technology which can produce various types of decorative and attractive designs on the surface of the fabric.

Process of printing 100% katoen:
Printing is the most used process. Process of printing varies, due to the types of fiber. When printing natural fibers such as cotton, wool and silk, the impurities on natural fibers must be removed before dyeing and printing. The process is also called as pre-treatment process. After printing, finishing process is carried out for improve the out looking of the printed fabric.

Inspection of grey cloth
↓
Stitching
↓
Shearing or Cropping
↓
Singeing
↓
Desizing
↓
Washing
↓
Skuur
↓
Bleiking
↓
Washing
↓
Stentering
↓
Druk
↓
Steaming
↓
Washing
↓
Agenda
↓
Inspection
↓
Folding or Rolling
↓
Packing

Emboss printing also called as pub printing, differs from pigment printing, foil printing, flock printing or any others dyes printing, which is particularly used for making logo or other decorative purpose. In this printing process, printing is done by embossing the printing paste on the textile materials.

Process of emboss printing (pub printing)
Resep: This is a sample recipe for emboss printing process.
Rubber paste: 49%
Pub/Emboss: 49%
Fixer: -2%

Fabric pre-treatment
↓
Table voorbereiding
↓
Stof gevleg op die tafel
↓
Apply printing paste by screen (3keer)
↓
Hanging for 15min
↓
Curing at 170℃ (belt speed 3m/min)
↓
Lewering

Emboss printing is mainly used for business card which can produce various types of glossy design.

Color fastness: Color fastness means the resistance to changes when subjected to particulars of condition which is specified in terms of changes and expressed in terms to the magnitude.

Color fastness to washing is used for measuring the fastness of colored materials, which is carried out in dyeing lab. Based on different measuring procedures, the test can be varied. For quality assurance system, a record is maintained for dyed fabrics or finished fabrics. Computer color matching system (CCMS) can save the record.

Required materials: The followings are necessary for wash fastness test:
1. Sample size 40 x 100 mm
2. Multi-fiber at 40 x 100 mm
3. ECE detergent (WOB)-4g/L
4. Sodium Perborate (Na2BO3.H2O2-1g/L)-1g/L
5. Distilled water
6. Noramal cold water
7. Steel balls

Required instruments: Various types of instrument are required for measuring color fastness to wash, including rota wash, scissor and stitch machine.

Steps for measuring color fastness to wash: Color fastness to wash is an off-line quality assurance.
1. Cut sample and multi-fiber at 40 x 100 mm.
2. Take the sample with 50 ml ECE detergent (WOB) en 50 ml Sodium per borate. For marks and Spencer, take the solution by formula: (Sample fabric + Multi-fiber weight) x 50 ml.
3. Keep the sample under 60℃ for 30 minutes in Rota wash machine.
4. Rinse the sample twice with cold water.
5. Dry at 60℃ by hanging or by Flat iron pression but temperature should not be more than 150℃.
6. Dry the specimen and the change of shade & degree of staining is measured by Grey Scale and Staining Scale.